HY Mono by Hy-Plugins

HY Mono by Hy-Plugins

Hy-Plugins / HY Mono

HY Mono

0 Stars

0 reviews | You must Create an Account and Log in to rate and review products.


The structure of this synth is based on Oberheim SEM.


Go to site

HY Mono by Hy-Plugins

Changes:
• added pan control to delay output
• added drive
• added limiter
• added randomize/clear button
• new gui

*this version doesn’t have backward compatibility,
so if you read old presets, it might sound different

v1.5.1(July 19, 2017)
• fixed samplerate change issue
• added VST3
• improved UI rendering speed

monophonic synthesizer
The structure of this synth is based on Oberheim SEM.

Update:

v1.01
fixed preset loading issue
v1.02
fixed delay time sync state not recall correctly
fixed vco frequency displays incorrect value
fixed “go to manual page” linked to wrong page
v1.03
changed location of settings file
v1.04
changed location of settings file
fixed automation issue
fixed value display issue.
v1.05
fixed sync delay time issue
minor changes
v1.1
improved interface design
added Mac version
som bug fixes


Demo Track


Signal Path

hyMono_signalPath


Preset

Changing Preset Folder Location

You can move “HYMONO” folder to where you like.
If you change preset folder location,
next time you need to set preset folder location.

 

Clicking preset menu button of HY-Mono, popup menu will show up like picture above.
If you select “Change Preset Folder Location“,
preset folder select window will show up like picture below.

hyMono_selectPresetFolder

You need to select “HYMONO” folder.
And next time HY-Mono will read preset files from that place.


Synth Parameters

VCO
There are two VCO units + Sub/Noise unit.
Each VCO unit can generate saw/pulse waveform.

Frequency
Bigger knob = coarse(range: -24 to +24 semitones)
Smaller knob = fine(-3 to +3 semitones)

Modulation
Frequency or Pulse width of oscillator can be modulate by envelope/lfo

Pulse Width
Set pulse width of pulse waveform(not affect to saw waveform)

Sync
Turn on sync button, oscillator of VCO2 will be synced to oscillator of VCO1.

Sub
select waveform of Sub oscillator

Mixer
You can control oscillator volume in VCF panel.

VCF

Frequency
cut-off frequency

Resonance
resonance level

Modulation
modulation depth(-100 to 100 %)
modulation source = Env2/LFO

Filter Type
you can control balance of lowpass and highpass
turn on “Bp” button, filter output switch to bandpass.

Mixer
you can control outputs of VCO section by three knobs at the bottom of VCF panel

 

ENV1/ENV2

ADSD type envelope generator
release rate is defined by decay value

Velo to Envelope

tick the velo box, envelope outputs will be affected by velocity input

LFO

LFO unit can generate sine waveform

Rate
LFO speed(0.1 to 55 Hz)

Phase
phase position of sine waveform
this setting is making sense when “LFO Reset” swith is active.

Delay

Time
delay time
turn on “S” swith, delay time is synced to host BPM.

Mod
delay time can be modulated by ENV1/LFO.

FB
feedback level

HP/LP
one pole filters for delay line outputs

Mix
mix level of delay effect outputs to main signal path

Output

you can control pan position  and master output level here.


Midi To CV

PitchBend Range
You can set PitchBend range here.(+/-1 to +/-12 semitone)

Note Priority
If multiple notes are pressed at the same time,
one of pressed notes will be given priority based on this setting.

 

Control Modes
Re-Trigger = If this switch is ON, Env1 and Env2 are always triggered by key press.
Filter Track = If this switch is ON, filter cutoff frequency will be affected by played note.
LFO Reset = IF this switch is ON, phase of LFO will be reset by key press.

Midi To Synth Params
You can modulate synth parameters by midi signal.

Source Menu = Velocity, ModWheel, AfterTouch, CC1, CC2
Target Menu = VCO1 Freq, VCO2 Freq, VCF Cf, VCA Amp, Pan, Delay Time
Knob = mod depth(-100~+100%)

Transpose
You can transpose incoming midi notes.(-2 ~ +2 octave)

Portamento
ON/OFF Swith = portamento on/off
Knob = portamento time


Randomize Setting
hyMono_randomize_setting

Ticked panels will be included randomize.
In this case, params of vco1, vcf, env2 and lfo will be randomized.


Re-Size Plugin Window 
hyMono_resize

You can re-size plugin window by pulling bottom right of the plugin window.